深圳市钜硕电子有限公司目前拥有12台全自动高速冲床、16台精密注塑机、8条全自动装配生产线、6台投影仪等一整套先进的生产、检验设备；现有员工480人。多年以来我们秉承着以制造和提供客户最满意的产品和服务，致力使“JUSHUO”成为世界品牌经营方针，针对日趋多样化的市场需求，不断开拓，创新，成功的开发了一系列新的产品并推向市场。产 品 规 格 书PRODUCT SPECIFICATION【1】适用范围 SCOPE本规格书适用于：0.5间距柔性扁平电缆连接器（有锁式）This specification covers the 0.5mm Pitch FPC/FFC Connectors（series Locking）【2】产品名称及型号 PRODUCT NAME AND PART NUMBER 产品名称Product Name产品型号Part NumberFFC/FPC扁平电缆连接器    【3】定格 RATINGS 项目 Item规      格        Requirement最大容许电压Rated Voltage(MAX)50V[AC/DC(有效值 Virtual value)50Hz]最大容许电流Rated Current(MAX)0.4A使用温度范围Ambienttemperature Range-25℃～ +85℃        【4】性能 PERFORMANCE4.1电气性能 Electrical Performance 项目Item条 件    Test Condition规格Requirement 4.1.1接触电阻Contact Resistance适合FPC/FFC嵌合；开放电压20mV以下；短路电流10mA的状态下测定。Mate applicable FPC/FFC and measure by dry circuit，20mV MAX，10mA.≤20 mΩMAX 4.1.2 绝缘电阻Insulation Resistance适合FPC/FFC嵌合；相邻端子间或端子与地面间加DC 500V下测定。Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground.500MΩMIN 4.1.3 耐电压Dielectric适合FPC/FFC嵌合；相邻端子间或端子与地面间加AC 200V（有效值）历时1分钟下测定。Mate applicable FPC/FFC and apply 200V AC（virtual value）for 1minute between adjacent terminal or ground.无击穿现象No Breakdown  4.2机械性能 Mechanical Performance项目Item条 件    Test Condition规格Requirement4.2.1锁紧力及拔出力Locking and Withdrawal Force适合0.3mm厚的FFC；用每分钟25±3mm的速度；平行地插入、锁紧、拔出。Insert and extract applicable FFC at the speed rate of 25±3mm/minute.锁紧力Locking1.96*n  (N)  MAX拔出力Withdrawal0.49*n  (N)  MIN4.2.2端子保持力Terminal  /Housing Retention Force以用每分钟25±3mm的速度平行向外拉Pull the terminal at the speed rate of 25±3mm per minute3.92N  MIN 4.3环境和其他性能 Environmental Performance and Others项目Item条 件    Test Condition规格Requirement 4.3.1重复插拔Repeated Insertion and Withdrawal无通电状态；以10次/分钟的速度插拔20次Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute接触抵抗Contact Resistance60 mΩMAX4.3.2温度上升Temperature Rise适合FPC/FFC嵌合；最大容许电流通电，温度测定。（UL 498）Carrying rated current load.（UL 498）温度上升Temperature Rise30℃MAX   项目Item条 件    Test Condition规格Requirement 4.3.3 耐振动性VibrationDC 1mA通电状态下；嵌合轴沿XYZ三个方向振动；振幅1.5mm；频率10-55-10Hz/分；历时2小时Amplitude：1.5mm P-PSweep time：10-55-10Hz in 1 minuteDuration：2 hours in each X.Y.Z. axes外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX瞬断Discontinuity1 ms MAX. 4.3.4 耐冲击性ShockDC 1mA通电状态下；嵌合轴沿相互垂直的6个方向；以490m/s2{50G}冲击；各3次490m/s2{50G}，3 strokes in each X.Y.Z. axes.外观Appearance无损坏No Damage瞬断Discontinuity1 ms MAX. 4.3.5 耐热性HeatResistance适合FPC/FFC嵌合；85±2℃的空气中；放置96小时；再回到室温中放置1-2小时85±2℃，96 hour外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX 4.3.6 耐寒性ColdResistance适合FPC/FFC嵌合；-40±2℃的空气中；放置96小时；再回到室温中放置1-2小时-40±2℃，96 hour外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX  4.3.7  耐湿性Humidity 适合FPC/FFC嵌合；40±2℃、相对湿度90-95%的空气中；放置96小时；再回到室温中0.5小时内测定 Temperature：40±2℃Relative Humidity：90-95%Duration：96 Hours外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX耐电压DielectricStrength必须满足4.1.3Must meet 4.1.3绝缘抵抗Insulation Resistance20 MΩMIN 4.3.8 温度循环TemperatureCycling适合FPC/FFC嵌合；-55±3℃ 30分钟；常温常湿 10-15分钟；85±2℃ 30分钟；常温常湿 10-15分钟，循环5次。5 cycles of：  a) -55±3℃    30 minutesb) 85±2℃    30 minutes外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX  项目Item条 件    Test Condition规格Requirement 4.3.9 耐盐雾性Salt Spray适合FPC/FFC嵌合；35±2℃、5±1%的盐水喷雾48小时；试验后常温水洗；再室温干燥。48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃.外观Appearance无损坏、腐蚀No Damage接触抵抗Contact Resistance60 mΩMAX 4.3.10 耐亚硫酸SO2 Gas适合FPC/FFC嵌合；40±2℃、50±5ppm的亚硫酸中放置24小时24 hours exposure to 50±5ppm. SO2 gas at 40±2℃.接触抵抗Contact Resistance60 mΩMAX 4.3.11 耐氨性NH3 Gas适合FPC/FFC嵌合；浓度为28%的氨水容器中；放置40分钟。40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution外观Appearance无损坏No Damage接触抵抗Contact Resistance60 mΩMAX 4.3.12 可焊性Solder ability端子前端基准面0.2mm处浸入235±5℃的锡槽中；历时2±0.5 sec。Soldering Time：2±0.5 sec.Soldering Temperature：235±5℃0.2 mm from terminal tip沾敷性Solder Wetting沾敷面积95%以上  4.3.13 耐焊接热Resistance toSoldering heat端子前端基准面0.2mm处浸入260±5℃的锡槽中；历时5±0.5 sec。Soldering Time：5±0.5 sec.Soldering Temperature：260±5℃0.2 mm from terminal tip外观Appearance无损坏、变形No Damage                                           (     )：参考规格Reference Standard{     }：参考单位Reference Unit【5】外观形状、寸法及材质PRODUCT SHAPE,DIMENSIONS AND MATERIALS图面参照 Refer to the drawing.名称 NAME材质    MATERIALS主体Main bodyLCP(本色)   UL 94V-0锁扣Housing  LockLCP(黑色)   UL 94V-0端子Sit uip磷青铜  Phosphor Bronze焊片Contact磷青铜  Phosphor Bronze备注Remark金属表面镀锡