FPC连接器FPC插座FPC插座连接器FPC插头座FFC连接器FFC插座FFC插座连接器FFC插头座 产 品 规 格 书PRODUCT SPECIFICATION【1】适用范围SCOPE本规格书适用于：0.5间距柔性扁平电缆连接器（有锁式）This specification covers the 0.5mm Pitch FPC/FFC Connectors（series Locking）【2】产品名称及型号PRODUCT NAME AND PART NUMBER产品名称Product Name        产品型号Part NumberFFC/FPC扁平电缆连接器    【3】定格RATINGS项目  Item 规     格         Requirement最大容许电压Rated Voltage(MAX)      50V   [AC/DC(有效值Virtual value)50Hz]最大容许电流Rated Current(MAX)     0.4A使用温度范围Ambient temperature Range     -25℃～+85℃   【4】性能PERFORMANCE4.1电气性能Electrical Performance项目Item   条 件    Test Condition  规格Requirement4.1.1   接触电阻Contact Resistance         适合FPC/FFC嵌合；开放电压20mV以下；短路电流10mA的状态下测定。Mate applicable FPC/FFC and measure by dry circuit，20mV MAX，10mA.       ≤20 mΩMAX4.1.2   绝缘电阻Insulation Resistance     适合FPC/FFC嵌合；相邻端子间或端子与地面间加DC 500V下测定。Mate applicable FPC/FFC and apply 500V DC between adjacent terminal or ground.       500MΩMIN4.1.3   耐电压Dielectric     适合FPC/FFC嵌合；相邻端子间或端子与地面间加AC 200V（有效值）历时1分钟下测定。Mate applicable FPC/FFC and apply 200V AC（virtual value）for 1minute between adjacent terminal or ground.       无击穿现象No Breakdown4.2机械性能Mechanical Performance项目Item   条 件    Test Condition  规格Requirement4.2.1   锁紧力及拔出力Locking and Withdrawal Force适合0.3mm厚的FFC；用每分钟25±3mm的速度；平行地插入、锁紧、拔出。Insert and extract applicable FFC at the speed rate of 25±3mm/minute.        锁紧力Locking1.96*n  (N)  MAX拔出力Withdrawal0.49*n  (N)  MIN4.2.2   端子保持力Terminal  /Housing Retention Force        以用每分钟25±3mm的速度平行向外拉Pull the terminal at the speed rate of 25±3mm per minute     3.92N  MIN 4.3环境和其他性能Environmental Performance and Others项目Item   条 件    Test Condition  规格Requirement 4.3.1   重复插拔Repeated Insertion and Withdrawal 无通电状态；以10次/分钟的速度插拔20次Insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute      接触抵抗Contact Resistance          60 mΩMAX4.3.2   温度上升Temperature Rise  适合FPC/FFC嵌合；最大容许电流通电，温度测定。（UL 498）Carrying rated current load.（UL 498）   温度上升Temperature Rise   30℃MAX项目Item   条 件    Test Condition  规格Requirement4.3.3   耐振动性Vibration       DC 1mA通电状态下；嵌合轴沿XYZ三个方向振动；振幅1.5mm；频率10-55-10Hz/分；历时2小时Amplitude：1.5mmP-PSweep time：10-55-10Hz in 1 minuteDuration：2 hours in each X.Y.Z. axes      外观Appearance 无损坏No Damage接触抵抗Contact Resistance          60 mΩMAX瞬断Discontinuity         1 ms MAX.4.3.4   耐冲击性Shock   DC 1mA通电状态下；嵌合轴沿相互垂直的6个方向；以490m/s2{50G}冲击；各3次490m/s2{50G}，3 strokes in each X.Y.Z. axes.         外观Appearance 无损坏No Damage瞬断Discontinuity         1 ms MAX.4.3.5   耐热性HeatResistance    适合FPC/FFC嵌合；85±2℃的空气中；放置96小时；再回到室温中放置1-2小时85±2℃，96 hour外观Appearance 无损坏No Damage接触抵抗Contact Resistance          60 mΩMAX4.3.6   耐寒性ColdResistance    适合FPC/FFC嵌合；-40±2℃的空气中；放置96小时；再回到室温中放置1-2小时-40±2℃，96 hour        外观Appearance 无损坏No Damage接触抵抗Contact Resistance          60 mΩMAX4.3.7   耐湿性Humidity     适合FPC/FFC嵌合；40±2℃、相对湿度90-95%的空气中；放置96小时；再回到室温中0.5小时内测定Temperature：40±2℃Relative Humidity：90-95%Duration：96 Hours      外观Appearance 无损坏No Damage接触抵抗Contact Resistance          60 mΩMAX耐电压DielectricStrength       必须满足4.1.3Must meet 4.1.3绝缘抵抗Insulation Resistance      20 MΩ MIN4.3.8   温度循环TemperatureCycling        适合FPC/FFC嵌合；-55±3℃30分钟；常温常湿10-15分钟；85±2℃30分钟；常温常湿10-15分钟，循环5次。5 cycles of：  a) -55±3℃    30 minutesb) 85±2℃    30 minutes     外观Appearance 无损坏No Damage接触抵抗Contact Resistance          60 mΩMAX项目Item   条 件    Test Condition  规格Requirement4.3.9   耐盐雾性Salt Spray    适合FPC/FFC嵌合；35±2℃、5±1%的盐水喷雾48小时；试验后常温水洗；再室温干燥。48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃.   外观Appearance 无损坏、腐蚀No Damage接触抵抗Contact Resistance          60 mΩMAX4.3.10 耐亚硫酸SO2 Gas      适合FPC/FFC嵌合；40±2℃、50±5ppm的亚硫酸中放置24小时24 hours exposure to 50±5ppm. SO2 gas at 40±2℃.        接触抵抗Contact Resistance          60 mΩMAX4.3.11 耐氨性NH3 Gas     适合FPC/FFC嵌合；浓度为28%的氨水容器中；放置40分钟。40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution    外观Appearance 无损坏No Damage      接触抵抗Contact Resistance          60 mΩMAX4.3.12 可焊性Solder ability         端子前端基准面0.2mm处浸入235±5℃的锡槽中；历时2±0.5 sec。Soldering Time：2±0.5 sec.Soldering Temperature：235±5℃0.2 mmfrom terminal tip        沾敷性Solder Wetting       沾敷面积95%以上4.3.13 耐焊接热Resistance toSoldering heat        端子前端基准面0.2mm处浸入260±5℃的锡槽中；历时5±0.5 sec。Soldering Time：5±0.5 sec.Soldering Temperature：260±5℃0.2 mmfrom terminal tip        外观Appearance 无损坏、变形No DamageReference Standard ：参考单位Reference Unit【5】外观形状、寸法及材质PRODUCT SHAPE,DIMENSIONS AND MATERIALS图面参照Refer to the drawing.名称  NAME    材质     MATERIALS主体Main body   LCP(本色)   UL 94V-0锁扣Housing  Lock     LCP(黑色)   UL 94V-0端子Sit uip磷青铜  Phosphor Bronze焊片Contact      磷青铜  Phosphor Bronze备注Remark        金属表面镀锡