产品用于各种精密设备.1.Standard Operating Conditions:标准运行条件1-1.Rated Voltage                    7.0 V DC constant额定电压1-2.Operating Voltage Range          3.5～9.0V DC at motor terminals工作电压范围1-3.Rated Load                       3.0 Kgf.cm 额定负载1-4.Excess Torque                   with-standing the max torque 20 Kgf.cm .最大承受力矩1-5.Direction of Rotation            CW when viewed from output shaft side.旋转方向                         CW：从输出轴端看为顺时针1-6.Motor Position                   All direction of protruded shaft摆放位置                         伸出轴的任意方向1-7.Operating Temperature Range      -5℃～+50℃工作温度范围 2.Measuring Conditions:测量条件2-1.Motor Position                   Horizontally or Vertical电机位置                         水平或垂直。2-2.Power Supply                     Regulated power supply which assures电  源                         　unquestionable measurement                                   经过调节的直流电源以确保无问题测量。2-3.Environment Temperature and Humidity                         环境温度与相对湿度    The test is made in principle at theTemperature　between 10℃and30℃,andat relative Humidity　between 30%and95%,Ifthetestresultisquestionable,it shall be judged from the test madeat JIS Standard Testing Condition(20±2℃,65%±5%RH).该试验原则上在温度为10℃~30℃之间、相对湿度在30%~95%之间进行。如果对试验结果有疑问，则应根据JIS标准试验条件下（20±2℃,65%±5%相对湿度）进行的试验进行判断。2-4.Unless otherwise specified,rated voltage to be applied.除非特别注明，使用额定电压。3. Electrical characteristics电气参数 3-1.No-load Speed                   29±15%   rpm空载转速3-2.No-load Current                 150 mA    Max空载电流3-3.Rated Speed                     25±15%   rpm额定转速3-4.Rated Current                   500 mA     Max额定电流3-5.Stall Torque                    18Kg.cm    Min堵转力矩                      3-6.Insulation Resistance           10MΩ Min. at 250V DC meg.绝缘电阻3-7.Endurance Voltage               1 mA/s Max  at 600V/AC.耐电压3-8.ReferenceCharacteristicCurve  See spec No.：37JPG3429-22200-150参考特性曲线3. Electrical characteristics电气参数 3-1.No-load Speed                   29±15%   rpm空载转速3-2.No-load Current                 150 mA    Max空载电流3-3.Rated Speed                     25±15%   rpm额定转速3-4.Rated Current                   500 mA     Max额定电流3-5.Stall Torque                    18Kg.cm    Min堵转力矩                      3-6.Insulation Resistance           10MΩ Min. at 250V DC meg.绝缘电阻3-7.Endurance Voltage               1 mA/s Max  at 600V/AC.耐电压3-8.ReferenceCharacteristicCurve  See spec No.：37JPG3429-22200-150参考特性曲线4.Mechanical Structure and Character:    机械特性4-1.Appearance                      No remarkable deformation and/or superficial defects.          外  观                         表面无明显变形或缺陷。                   4-2.Dimension                      AsperdimensionaldrawingNo.：37JPG3429-22200-150    外形图                          符合尺寸图纸No.：37JPG3429-22200-1504-3.Weights                         180g (Approx)重  量4-4.Shaft End Play                  0.5mm  Max轴端间隙4-5.Mechanical Noise                55dB   Max            机械噪音                       Mechanical noise under No-load at Rated Voltage                                                                                    (Back ground noise to be 29dB (A)max).额定电压无负载时的机械噪音。     (背景噪音最大为30dB (A))4-6.Vibration                       To be set up with mutual consent.振  动                          达到双方同意的标准。 5. Motor life test:寿命试验5-2.Voltage                          7.0 V DC电  压5-3.Load                             3.0 Kgf.cm 负  载  5-4.Environment                      25℃±5℃/ 65%±20%RH测试环境                  5-5.Duty Cycle                       As sketched below.测试模式                         连续运转Life end defined as follows:按如下状态确定寿命终结：1)   When current is over±30%against the initial figure.电流与初始状态下的电流有±30%的差异。2）When speed is beyond±30%   against the initial figure.  转速与初始状态下的转速有±30%的差异。3)   When motor is unquestionablerecognized as unusable.      电机被明显确认为不可使用。5-6.Life Expectancy:            300 Hrs MIN期望寿命          6. Storage贮 存6-1.Storage Temperature                 -20℃~ +70℃.储存温度6-2.Storage Relative Humidity           10%~90%.储存湿度  6-3.Keep dry, avoid storing in high temperature、high humidity or corrosive gas environment.保持干燥，避免放置在高温、潮湿及有腐蚀性气体的环境中。7. CAUTIONS：注意事项7-1.Since the performance of the motor is affected by environmental temperature,condition be give to keep it away from out of range.环境温度条件对马达性能有极大影响，请在本技术指标范围内使用马达。7-2.It is not allowed to operate in the high temperature with high humidity or in therust or in the circumstance where the substances generating a harmful gas suchas low molecular Siloxane, syan, formalin ,quick-dry glue or the corrosive gas suchas H2S, SO2, XO2, Cl, exist.避免在高温、高湿及与腐蚀液体、气体接触。7-3. Do not lock the motor shaft while the electric is on .   If lock state more than 1 minute would or resistor is heated up and may burnt  but not start fire.  请不要在马达运行时锁定电机轴。若持续锁定超过1分钟，马达将发热甚至烧毁。7-4. Do not give direct shock to the motor.    应避免直接碰撞马达。